Post Buying Request
 

Abrasive Grains

As a kind of materials, abrasive grains can be distinguished in a variety of ways. They are classified as either natural or synthetic abrasives by manufacturing; either conventional or super abrasives by using history.Learn more

Pink Fused Alumina Specifications

Learn more
Learn more
Learn more
Learn more

Guide for Pink Fused Alumina Specifications

Form

The raw abrasive materials or ingots are crushed and sized from blocks to grains and powders ranging from macrogrits to microgrits.

Block:Blocky raw abrasive materials or ingots that are crushed by various crushers, which gradually break them up into smaller or manageable sizes.

Grain:A small, hard particle or crystal of abrasive materials that are typically sized or graded by a series of mesh sieves.

Powder:Much finer grits that are separated by hydraulic flotation and sedimentation or by air classification.

Particle Shape

The particle shape of abrasive grains affects their performance in various ways, such as the subsurface damage level and stock removal rate.

Angular:An angular abrasive has sharp but not weak, platy or needlelike edges, which ensure the quickest cleaning rate when removing tightly adhering material or contamination from the substrate.

Blocky:A blocky or rounded abrasive has mostly flat edges. The blocky shape enhances toughness and bulk density of the grain, providing good cleaning rate in most applications, except for those substrates with hard-to-remove contaminants.

Sharp:A sharp abrasive has much sharper edges than the angular one. They are generally required for producing aggressive and fast cutting coated abrasives, grinding wheels, etc.

Irregular:A variety of highly irregular shapes are possible through different manufacturing processes for specific applications. Typically, the irregular or crushed shapes are very angular with sharp edges for abrading, cutting or grinding.

Other:Other unusual shapes for abrasive materials.

Grading System

Abrasives are measured by different grading system standards that define a limited range of particle sizes for each grade. So the grit size designations are not consistent across different grading systems.

ANSI:American grading or grit size standards for abrasive grains. ANSI stands for "American National Standards Institute".

FEPA:European grading or grit size standards for abrasive grains. FEPA stands for "Federation of European Producers of Abrasives Products".

JIS:Japanese grading or grit size standards for abrasive grains. JIS stands for "Japanese Industrial Standards".

ISO:International grading or grit size standards for abrasive grains. ISO stands for "International Organization for Standardization".

GB/T:Chinese grading or grit size standards for abrasive grains.

SAE:"Society of Automotive Engineers" (SAE) grading or grit size standards for sand blasting.

Other:Other unlisted, proprietary, or specialized grading or grit size system.

Features

Low Heat-treated:Low temperature treatment enhances the toughness of abrasive grain, also improves cleanliness and capillarity. Heat-treated abrasive materials can be used for the fabrication of grinding wheels, coated abrasives, and specialized industrial applications.

High Heat-treated:High temperature treatment imparts a blue color to the abrasive grain, as well as enhances its toughness. Heat-treated abrasive materials can be used for the fabrication of grinding wheels, coated abrasives, and specialized industrial applications.

Surface Treated:Surface Treatment is one process applied to abrasive grain by a variety of methods, such as silane treatment, projectivity enhancing treatment, iron oxide coating, etc. Most of them may be applied to improve resin’s bonding effects for grinding wheel and sandpaper, or enhance wettability, flowability, suspension in water or oil, or strengthen other characteristics.

Ultra-Fine:Particle size is finer than 1 micron, which is suitable for a wide range of lapping and polishing applications. It can be used in suspension, slurry or paste form.

Applications

Bonded Abrasives:Bonded abrasives are made of natural or synthetic abrasive grains which are bound together with a vitrified or resinoid or other bond into a mold usually in the shape of a wheel, then pressed and fired at high temperatures. Bonded abrasives, which can be made from different materials, come in thousands of shapes and sizes depending on the type needed and specific application required, such as cutting-off and grinding wheels, snagging wheels, mounted wheels, segments, honing stones, plugs, cones, etc.

Blasting:Abrasives are used as blasting media, to clean or prepare surfaces prior to applying coatings or to produce a desired surface profile, by propelling very fine bits of material at high-velocity. Blasting is used for finishing, surface texturing, roughening, frosting/ etching, degreasing, deburring, deflashing, descaling, stripping of coatings, and surface preparation of products made of metal, wood, plastic, glass, or other materials. Any small, relatively uniform particles will work, such as steel grits, copper slags, walnut shells, powdered abrasives, even bits of coconut shells.

Cleaning/ Surface Prep:Abrasives are used as finishing media for cleaning and surface preparation products, applied for cleaning, degreasing, de-oiling, texturing, descaling, discoloration removal, roughening, and other surface preparation applications.

Coated Abrasives:Abrasive grains are used to make coated abrasives such as sandpaper and are available in sheets, discs, rolls, belts, pads, flap wheels, and other forms. Coated abrasives are a product of three basic elements: abrasive grains, bond and backing. Abrasive grains can be either natural or synthetic, such as aluminum oxide, silicon carbide, zirconia alumina, garnet, emery, etc. The abrasive grain is adhered to a cloth, fiber, paper or polyester film backing by a resin or glue or other bond. Abrasive grains should exhibit high capillarity for instant adhesion to bonds.

Deburring/ Deflashing:Abrasives are designed or suitable for applications such as removing burrs, sharp corners, part or welding lines and flash (deflashing).

Descaling/ Stripping:Abrasive grits or media are designed or suitable for descaling or coating stripping applications.

Fast Cutting/ Aggressive:Coarse grit abrasives are typically designed or suitable for fast cutting and aggressive applications such as heavy duty cutting or hard materials removal.

Grinding/ Ball Milling:Abrasive media are applied for ball milling or grinding down of a solid material or powder into smaller pieces or finer powders. The material being ground and the media (ceramic bead, hard metal shot, carbide balls or other ball shaped media) are filled in the ball mill for rotating, grinding and mixing by mechanical forces. The hardness of the material or powder being ground determines what kind of media's material will be selected. Media grinding or ball milling is widely used in producing cement, silicate, new type building materials, fireproofing, chemical fertilizer, black and non-ferrous metal, and glass ceramics. Besides, also used to produce alloys from metal powders.

Polishing/ Lapping:Finer abrasive grains are used to make polishing/lapping compounds, coated abrasive lapping films, superfinishing bonded abrasives, etc. Polishing and lapping are characterized by very fine surface finishes, high dimensional accuracy and flatness, and minimal subsurface damage. They are the precision processes applied for mechanical and electronic or semiconductor components, to produce a smooth, bright and lustrous surface.

Refractory:Abrasive grains that have excellent chemical stability and thermal property, such as fused mineral brown fused alumina, have hundreds of different applications as refractory materials due to their ability to withstand continuous exposure to the combination of heat, corrosion, abrasion and impact. 

Tumbling/ Mass Finishing:Abrasives are used as or for the fabrication of tumbling and mass finishing media for the applications of deburring, burnishing, coloring, descaling, polishing or cleaning for parts and components during finishing processes. The selection of shape (such as ball, cone, ballcone, wedge, pin, taper, cylinder, cut wire, diagonal, angle cut, diamond, cube, oval ball, eclipse or ball with flat, crushed grit, pyramid, triangle, and star or tristar) and material (such as natural and synthetic abrasive grain, metal, ceramic, plastic, wood, nutshell, corncob, carbonate or mineral) of tumbling and mass finishing media should be selected depend on particular tasks.

Specialty:Other unlisted grinding, blasting, finishing, and abrasives applications.

Sponsored links